AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |
Back to Blog
Hauppauge wintv dualhd tv tuner ubuntu3/20/2024 Usually getting around these values so signal should be fine. I have this DVB+Analog usb tv tuner Hauppauge WinTV HVR-900 (r2) USB ID 2040:6502. The device is supported, based on LinuxTV. I have a WinTV HVR 1900 TV tuner runnning on Ubuntu 13.10, from which I would like to capture S-VIDEO input. ![]() si2168 4-0067: firmware version: B 4.0.11 Hauppauge WinTV-dualHD not working on ubuntu 18.04. Linux ubuntuvm 4.15.0-47201904171620-generic #0+mediatree+hauppauge-Ubuntu SMP Wed Apr 17 22:20: x86_64 x86_64 x86_64 GNU/LinuxĪt least the firmware seems to be the same on different setups. Drivers installed as instructed by Hauppauge VirtualBox extension pack installed using USB 2.0 Hauppauge Digital has teamed up with Mac software developer Elgato to deliver. VirtualBox guest on Ubuntu host, tried also on macOS host This tool is for use with the WinTV-dualHD, WinTV-HVR-955Q and the WinTV-NOVA-S2 and 461e Display or change the USB transfer mode of your Hauppauge TV tuner You can use the following Windows tool (runs under Windows 11, 10, 8 or 7) to reprogram a WinTV-dualHD isoc stick to bulk mode and vice versa. The Hauppauge WinTV Nova-TD Diversity Stick comes with two Freeview digital TV tuners - and its now Mac-compatible. Linux telkkari 4.14.78-4-osmc #1 SMP PREEMPT Wed Dec 12 17:58: armv7l GNU/Linux Latest version and all patches installed Using same cables with each setup and also shorter cables. Somehow I'm feeling it is some driver or other software issue as everything works out of the box with OSMC and not with Ubuntu by following Hauppauge guidance. Where I should start investigating and what to try in order to get that Ubuntu work with Tvheadend and my tuner properly? I wonder is the problem with VirtualBox or software installed by following Hauppauge guide. However, by searching I see that others have had similar issues. Actually I'm not even thinking Tvheadend is the problem as I'm not able to get the picture on another Ubuntu 18.04 Desktop with Kaffeine player either. I would prefer running Tvheadend on that Ubuntu though as it is easier to arrange large disk, fast network and reasonable performance for it. Then everything works just nicely on OSMC on Raspberry Pi. Usually the playback is not starting at all on VLC. I'm getting around 20 000 Continuity Errors in couple of minutes and can't see a single proper frame. In the Device Setup Wizard, you will see a list of TV formats which your Hauppauge TV tuner can support. Then click on the Devices tab and highlight your WinTV device and click Tuner Setup (see the first picture below). Hope you figure it out.I'm having enormous amount of Continuity Errors with Hauppauge WinTV-dualHD on Ubuntu 18.04 Server running as VirtualBox guest. Click on the setting button (Gear) in the lower left of the WinTV v10 application. I did find some other issues later with shows that always failed.you can probably still find my posts if you search. I used the instructions posted here on the forum to install NextPVR and I don't recall having any issues with scanning, it mostly just ran. ![]() I was running Ubuntu Server 20.04 on the Pi, the 64 bit version.I had run into some issues with file size limitations using the 32 bit version. See Īctually, I haven't used NextPVR or been on the forum for quite a while now so I can't speak to the latest version. ![]() ![]() I ask because the "Scan Channels" feature does not currently function in NextPVR v5 on my Raspberry Pi 4 running the latest version of the Raspberry Pi OS (32-bit) - apparently there is some kind of issue with dvbv5-scan not working for the Pi. (, 09:11 PM)MattDuffy Wrote: Hi zed, I'm curious as to how you were able to get NextPVR working on your Raspberry Pi 4? Which OS are you running?
0 Comments
Read More
Leave a Reply. |